Adament FLOW Almond Fungicide

Fungicide

Adament™ FLOW Fungicide, now with a liquid design, is engineered for effective disease control in almonds against Alternaria, Red Leaf Blotch (RLB), scab, and rust.

Approved In

Product Details

Group Number	Formula	Registration Number
GROUP TEBUCONAZOLE FUNGICIDE	liquid	0000264-00849-AA-0000000

Active Ingredients

Active Ingredient	Formulation
Tebuconazole	22.63 %
Trifloxystrobin	22.63 %

Labels / Safety Data Sheets (MSDS)

Additional Downloads

Use and Mixing

The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email or call 1-866-99-BAYER.

Adament FLOW Almond Fungicide

MIXING INSTRUCTIONS

Adament Flow Alone: Add approximately 1/2 of the required amount of water to the mix tank. With the agitator running, add the Adament Flow to the tank. Continue agitation while adding the remainder of the water. Begin application of the solution after the ABSOLUTE has completely and uniformly dispersed into the mix water. Maintain agitation until all of the mixture has been applied.

Reentry PPE

PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water is:\r\n- Coveralls over long-sleeved shirt and long pants\r\n- Chemical-resistant gloves made of any waterproof material\r\n- Shoes plus socks

PPE

Personal Protective Equipment (PPE) Applicators and other handlers must wear: - Long-sleeved shirt and long pants - Shoes plus socks - Chemical-resistant gloves made of any waterproof material

Tankmix Compatibility

Adament Flow + Tank Mix Partners: Add approximately 1/2 of the required amount of water to the mix tank. Start the agitator running before adding any tank-mix partners. In general, tank-mix partners must be added in this order: products packaged in watersoluble packaging*, wettable powders, wettable granules (dry flowables), liquid flowables such as ABSOLUTE, liquids, and emulsifiable concentrates. Always allow each tank-mix partner to become fully and uniformly dispersed before adding the next product. Provide sufficient agitation while adding the remainder of the water. Maintain agitation until all of the mixture has been applied. * Note: When using Adament Flow in tank mixtures, all products in water-soluble packaging must be added to the tank before any other tank-mix partner, including Adament Flow. Allow the water-soluble packaging to completely dissolve and the product(s) to completely disperse before adding any other tank-mix partner to the tank. If using Adament Flow in a tank mixture, observe all directions for use, crop/sites, use rates, dilution ratios, precautions, and limitations which appear on the tank-mix partner product label. No label dosage rate must be exceeded, and the most restrictive label precautions and limitations must be followed. This product must not be mixed with any product which prohibits such mixing. Tank mixtures or other applications of products referenced on this label are permitted only in those states in which the referenced products are registered. Adament Flow is compatible with most insecticide, fungicide, and foliar nutrient products. However, the physical compatibility of Adament Flow with tank-mix partners must be tested before use. To determine the physical compatibility of Adament Flow with other products, use a jar test, as described below. Using a quart jar, add the proportionate amounts of the products to 1 qt. of water. Add wettable powders and water-dispersible granular products first, then liquid flowables, and emulsifiable concentrates last. After thoroughly mixing, let stand for at least 5 minutes. If the combination remains mixed or can be remixed readily, it is physically compatible. Once compatibility has been proven, use the same procedure for adding required ingredients to the spray tank. The crop safety of all potential tank mixes including additives and other pesticides on all crops has not been tested. Before applying any tank mixture not specifically directed on this label, the safety to the target crop should be confirmed. To test for crop safety, apply Adament Flow to the target crop in a small area and in accordance with label instructions for the target crop.