Adament Fungicide Use & Mixing
The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Please click on 'Labels / MSDS' in the left hand navigation for special or state label instructions. Always read and follow label instructions.
Adament 50 WG Fungicide
- MIXING PROCEDURESPrepare no more spray mixture than is needed for the immediate operation. Thoroughly cleanspray equipment before using this product. Vigorous agitation is necessary for proper dispersal of the product. Maintain maximum agitation throughout the spraying operation. Do not let the spray mixture stand overnight in the spray tank. Flush the spray equipment thoroughly following each use and apply the rinsate to a previously treated area.ADAMENT 50 WG Fungicide Alone: Add approximately 1/2 of the required amount of waterto the mix tank. With the agitator running, add the ADAMENT 50 WG Fungicide to the tank.Continue agitation while adding the remainder of the water. Begin application of the solution after the ADAMENT 50 WG Fungicide has completely and uniformly dispersed into the mix water.Maintain agitation until all of the mixture has been applied.
- Reentry PPE
- PPE required for early entry to treated areas that is permitted under the Worker ProtectionStandard and that involves contact with anything that has been treated, such as plants,soil, or water, is:- Coveralls- Chemical-resistant gloves made of any waterproof material- Shoes plus socks
- Personal Protective Equipment (PPE)Applicators and other handlers must wear:- Long-sleeved shirt and long pants- Shoes plus socks- Chemical resistant gloves made of any waterproof materialFollow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry.
- ADAMENT 50 WG Fungicide + Tank Mix Partners: Add approximately 1/2 of the required amountof water to the mix tank. Start the agitator running before adding any tank mix partners. In general, tank mix partners should be added in this order: products packaged in water-soluble packaging*, wettable powders, wettable granules (dry flowables), liquid flowables, liquids, and emulsifiable concentrates. Always allow each tank mix partner to become fully and uniformly dispersed before adding the next product. Provide sufficient agitation while adding the remainder of the water. Maintain agitation until all of the mixture has been applied.* Note: When using ADAMENT 50 WG Fungicide in tank mixtures, all products in water-solublepackaging should be added to the tank before any other tank mix partner, including ADAMENT50 WG Fungicide. Allow the water-soluble packaging to completely dissolve and the product(s) to completely disperse before adding any other tank-mix partner to the tank. If using ADAMENT 50 WG Fungicide in a tank mixture, observe all directions for use, crop/sites, use rates, dilution ratios, precautions, and limitations which appear on the tank mix partner product label. No label dosage rate may be exceeded, and the most restrictive label precautions and limitations must be followed. This product must not be mixed with any product which prohibits such mixing. Tank mixtures or other applications of products referenced on this label are permitted only in those states in which the referenced products are registered.ADAMENT 50 WG Fungicide is compatible with most insecticide, fungicide, and foliar nutrient products. However, the physical compatibility of ADAMENT 50 WG Fungicide with tank mix partners should be tested before use. To determine the physical compatibility of ADAMENT 50 WG Fungicide with other products, use a jar test, as described below.Using a quart jar, add the proportionate amounts of the products to 1 quart of water. Add wettable powders and water-dispersible granular products first, then liquid flowables, and emulsifiable concentrates last. After thoroughly mixing, let stand for at least 5 minutes. If the combination remains mixed or can be remixed readily, it is physically compatible. Once compatibility has been proven, use the same procedure for adding required ingredients to the spray tank.The crop safety of all potential tank mixes, including additives and other pesticides, on all crops has not been tested. Before applying any tank mixture not specifically recommended on this label, the safety to the target crop should be confirmed. To test for crop safety, apply the tank mixture to the target crop in a small area and in accordance with label instructions for the target crop.
Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email
or call 1-866-99-BAYER.