Osprey Herbicide
CROP PROTECTION

Osprey Herbicide

Herbicide
Keep your crop choices open with the rotational flexibility of Osprey® herbicide and gain control over tough grassy weeds in your winter wheat. Osprey provides control of Group 1 resistant grasses in one pass.
Approved In
AL, AR, AZ, CA, CO, DC, DE, GA, IA, ID, IL, IN, KS, KY, LA, MA, MD, MI, MO, MS, MT, NC, ND, NE, NJ, NM, NV, OH, OK, OR, PA, SC, SD, TN, TX, UT, VA, WA, WV, WY
    Group NumberFormulaRegistration Number
    GROUP 2 HERBICIDE dry0000264-00802-AA-0000000

    Active IngredientFormulation
    Mesosulfuron-Methyl4.5 %

Labels / MSDS

Use and Mixin

Use and Mixing

The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email or call 1-866-99-BAYER.
      MIXING INSTRUCTIONS
      MIXING INSTRUCTIONS OSPREY Herbicide must be applied with clean and properly calibrated equipment. Prior to adding OSPREY Herbicide to the spray tank, ensure that the spray tank, filters, and nozzles have been thoroughly cleaned. Mixing Order 1. Fill the tank 1/4 to 1/3 full of water. 2. While agitating, add the required amount of OSPREY Herbicide. 3. Continue agitation until the OSPREY Herbicide is fully dispersed, at least 5 minutes. 4. Once OSPREY Herbicide is fully dispersed, maintain agitation and continue filling tank with water. OSPREY Herbicide should be fully mixed with water before adding any other material. 5. As the tank is filling, add the required amount of spray adjuvant (methylated seed oil or basic blend or non-ionic surfactant) and ammonium nitrogen fertilizer. Add additional pesticide tank mix partner, if desired. 6. Continue agitation during herbicide application to ensure uniform spray coverage. If the mixture is not continuously agitated, settling may occur. If settling occurs, thoroughly re-agitate spray solution for at least 10 minutes before application. Use spray solution within 24 hours after mixing.
      Reentry PPE
      PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated such as plants, soil or water, is coveralls, socks, shoes, chemical resistant gloves such as barrier laminate, butyl rubber >= 14 mils, nitrile rubber >= 14 mils, or neoprene rubber >= 14 mils, and protective eye wear.
      PPE
      PERSONAL PROTECTIVE EQUIPMENT (PPE) Some materials that are chemical-resistant to this product are listed below. If you want more options, follow the instructions for category A on an EPA chemical resistance category selection chart. Applicators and other handlers must wear: Long-sleeved shirt and long pants, socks, shoes, chemical resistant gloves such as barrier laminate, butyl rubber >= 14 mils, nitrile rubber >= 14 mils, or neoprene rubber >= 14 mils, and protective eyewear (safety glasses). Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
      Tankmix Compatibility
      COMPATIBILITY If OSPREY Herbicide is to be tank mixed with other herbicides, compatibility should be tested prior to mixing. To test for compatibility, use a small container and mix a small amount (0.5 to 1 qt) of spray solution, combining all ingredients in the same ratio as the anticipated use. If any indications of physical incompatibility develop, do not use this mixture for spraying. Indications of incompatibility usually occur within 5-15 minutes after mixing. Read and follow the label of each tank mix product used for precautionary statements, directions for use, geographic and other restrictions.


Recommended Agronomy Resources