Allegiance FL Seed Treatment Fungicide
CROP PROTECTION

Allegiance FL Seed Treatment Fungicide

SeedGrowth
Allegiance® FL Seed Treatment Fungicide provides systemic protection for the seed, roots and emerging plants against devastating diseases such as Pythium, systemic downy mildew and Phytophthora. It provides protection for early planted crops and helps produce healthier, more vigorous and uniform stands. Allegiance is applied at very low rates per acre, making it friendly to the grower, seed and environment.
Approved In
AL, AR, AZ, CA, CO, CT, DE, FL, GA, HI, IA, ID, IL, IN, KS, KY, LA, MD, MI, MN, MO, MS, MT, NC, ND, NE, NJ, NM, NV, NY, OH, OK, OR, PA, SC, SD, TN, TX, UT, VA, WA, WI, WY
    Group NumberFormulaRegistration Number
    GROUP 4 FUNGICIDE METALAXYL liquid0000264-00935-AA-0000000

    Active IngredientFormulation
    Metalaxyl28.35 %

Labels / MSDS

Use and Mixin

Use and Mixing

The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email or call 1-866-99-BAYER.
      MIXING INSTRUCTIONS
      Mixing Instructions 1. When applied with seed treatment application equipment designed to treat seed utilizing a treatment slurry mixture, add approximately 1/2 to 2/3 of the required water to the treatment slurry tank followed by the accompanying seed treatment products and ALLEGIANCE-FL Seed Treatment Fungicide. 2. The order of product addition is dependent on the accompanying seed treatment products and application equipment used. 3. Allow each slurry component to disperse completely prior to the next addition until a uniform suspension is obtained. 4. After all slurry components have been added and dispersed completely add the remaining 1/2 to 1/3 of required water for proper slurry volume and mix until uniform. 5. Do not store mixed slurries for greater than 72 hours. 6. Maintain adequate agitation until treatment slurry is applied. For additional instructions for use, slurry component mixing order, and other application suggestions contact your Bayer CropScience representative. Follow more restrictive labeling of any tank mix partner. Do not tank mix with any product, which contains a prohibition on tank mixing. ALLEGIANCE-FL Seed Treatment Fungicide may be applied as a water based slurry with other registered seed treatment insecticides and fungicides through standard slurry or mist-type commercial seed treatment equipment. It is the pesticide user's responsibility to ensure that all products are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. Excess treated seed may be used for ethanol production only if (1) by-products are not used for livestock feed and (2) no measurable residues of pesticide remain in ethanol byproducts that are used in agronomic practice.
      Reentry PPE
      PPE required for early entry to treated areas that is permitted under the Worker\r\nProtection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, is: coveralls, socks and chemical resistant footwear, chemical resistant gloves, barrier laminate or butyl rubber >= 14 mils, nitrile rubber >= 14 mills, polyvinyl chloride (PVC) >= 14 mils, and viton >= 14 mills or Viton and protective eyewear.
      PPE
      Some materials that are chemical-resistant to this product are: (barrier laminate, butyl rubber >= 14 mils, nitrile rubber >= 14 mills, polyvinyl chloride (PVC) >= 14 mils, and viton >= 14 mills). Applicators and other handlers must wear: Coveralls over short-sleeved shirt and short pants, socks and chemical-resistant footwear and chemical-resistant gloves (barrier laminate, butyl rubber >= 14 mils, nitrile rubber >= 14 mills, polyvinyl chloride (PVC) >= 14 mils, and viton >= 14 mills). Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
      Tankmix Compatibility
      COMPATIBILITY TESTING AND TANK MIX PARTNERS May be used in combination with other registered Bayer CropScience seed treatment fungicides and insecticides. Pre-test for compatibility with other seed treatment products. Compatibility It is essential that before using ALLEGIANCE-FL Seed Treatment Fungicide in any tank mixture the compatibility of the mixture be established. Add ALLEGIANCE-FL Seed Treatment Fungicide at the labeled rate to a clean quart jar containing approximately one-half the amount of water intended for a final slurry application rate. Next, follow with all other tank mix components that will be used in the total slurry application. Add last the remaining balance of water. The total amount of volume is determined by the seed size and how much is necessary to ensure complete and uniform coverage and distribution on the seed, as well as the type of commercial seed treating application equipment that will be used. DO NOT USE MIXTURES THAT CURDLE, PRECIPITATE, OR GEL. USE TANK MIXTURES IMMEDIATELY AFTER MIXING WITH ADEQUATE AGITATION.


Recommended Agronomy Resources