Harness Xtra 5.6L Herbicide Premix For Corn

Harness Xtra 5.6L Herbicide Premix For Corn

Harness® Xtra 5.6L herbicide is a premix of acetochlor (3.1 lbs ai/gal) and atrazine (2.5 lbs ai/gal) that offers an expanded spectrum of weed control in corn, including more than 40 grass and broadleaf weed species. Harness Xtra 5.6L herbicide provides excellent control in all tillage situations and is formulated to deliver a flexible rate range of acetochlor and atrazine depending on geography. In addition, this product has a flexible application window including preplant, preemergence, and early postemergence in corn up to 11 inches.
Approved In
    Group NumberFormulaRegistration Number
    HERBICIDES GROUP liquid0000524-00485-AA-0000000

    Active IngredientFormulation
    Acetochlor33.4 %
    Atrazine26.9 %

Use and Mixin

Use and Mixing

The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email or call 1-866-99-BAYER.
      Reentry PPE
      PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, are: coveralls, shoes plus socks and chemical-resistant gloves, made of any waterproof material.
      Some materials that are chemical-resistant to this product are listed below. Mixers, loaders, applicators and other handlers must wear: long-sleeved shirt and long pants, chemical-resistant gloves such as polyethylene or polyvinylchloride, shoes plus socks, and a chemical-resistant apron, when mixing/loading, cleaning up spills, or cleaning equipment, or otherwise exposed to the concentrate. See engineering controls for additional requirements. Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.
      Tankmix Compatibility
      8.2 Sprayer Compatibility Always predetermine the compatibility of this product or labeled tank mixtures of this product with water carrier or sprayable fluid fertilizer carrier by mixing small proportional quantities in advance. See the "STANDARD SPRAYABLE FLUID FERTILIZER COMPATIBILITY TEST" section in this label to determine the compatibility of this product and the labeled tank mixtures recommended for use with sprayable fluid fertilizer carrier. Mix this product or labeled tank mixture of this product with the appropriate carrier as follows: 1. Place a 20- to 35-mesh screen or wetting basket over filling port. 2. Through the screen, fill the sprayer tank one-half full with the appropriate carrier. 3. If a compatibility agent is necessary to improve mixing or to prevent the formation of undesirable and unsprayable gels or precipitates, while agitating add it to the carrier already in the tank. Use only compatibility agents cleared by FDA for this use. Read and follow all directions for use, cautionary statements and all other information appearing on the selected compatibility agent label. Check for adequate agitation. 4. If a wettable powder or dry flowable formulation is used, make a slurry with water, and add it slowly through the screen into the tank. Continue agitation. 5. If a flowable formulation is used, add slowly through screen into the tank. Mixing and compatibility may be improved when flowable is premixed one part flowable with one part water and added slowly to the tank in diluted form. 6. Add this product slowly through the screen into the tank. Mixing and compatibility may be improved when this product is prediluted with two parts of water and added to the tank in diluted form. 7. Complete filling the sprayer tank with carrier. If a Roundup(R) agricultural herbicide or Gramoxone brand herbicide is used, add the required amount near the end of the filling process. Remove hose from tank immediately after filling to avoid siphoning back into the water source. Maintain good agitation at all times until the contents of the tank are sprayed. NOTE: If spray mixture is allowed to settle at any time, thorough agitation is required to resuspend the mixture before spraying is resumed. Keep by-pass line on or near bottom of tank to minimize foaming. Screen size in nozzle or line strainers should be 50-mesh. Carefully select proper nozzle to avoid spraying a fine mist. Check for even distribution of spray droplets. To reduce loss of the chemical due to drift of a fine mist, apply at nozzle pressures below 40 psi. 8.3 Standard Sprayable Fluid Fertilizer Compatibility Test Herbicides may not always mix evenly throughout a sprayable fluid fertilizer or the components may separate too quickly to make their combined use of practical value. This may be due to certain characteristics of the different fluid fertilizers. A simple test using small quantities of the components is suggested to provide compatibility potential. The test follows: A. Materials Required For A Compatibility Test 1. Two one-quart jars with lid or stopper (marked "with" and "without"). 2. TEAspoons (for a more exacting test, a five to ten milliliter (mL) pipette or graduated cylinder is desirable). 3. Sprayable fluid fertilizer to be tested. 4. The herbicide chemicals to be mixed. 5. A compatibility agent (the purpose of the adjuvant is to help keep the fertilizer and crop protection chemical in suspension, if this assistance is needed).

Recommended Agronomy Resources