Download PDFdownload
Trivolt Herbicide
CROP PROTECTION

Trivolt Herbicide

Herbicide
Built with a proprietary formula, Trivolt™ Corn Herbicide provides burndown and residual activity in a variety of weather conditions.
Approved In
AL, AR, CO, DE, GA, IA, IL, IN, KS, KY, LA, MD, MI, MN, MO, MS, MT, NC, ND, NE, NJ, NM, OH, OK, PA, SC, SD, TN, TX, VA, WI, WV, WY
    Group NumberFormulaRegistration Number
    GROUP ISOXAFLUTOLE HERBICIDE liquid0000264-01211-AA-0000000

    Active IngredientFormulation
    Isoxaflutole5.7 %
    Flufenacet28.5 %
    Thiencarbazone-methyl2.28 %

Labels / MSDS
Additional Downloads

Use and Mixin

Use and Mixing

The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email or call 1-866-99-BAYER.
      MIXING INSTRUCTIONS
      MIX WELL BEFORE USE
      Reentry PPE
      PPE required for early entry to treated areas (that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, including plants, soil, or water), is:\r\n- Coveralls over long-sleeved shirt and long pants\r\n- Waterproof gloves\r\n- Socks plus chemical resistant footwear\r\n- Protective eye wear.
      PPE
      PERSONAL PROTECTIVE EQUIPMENT (PPE) Applicators and other handlers must wear: - Long-sleeved shirt and long pants. - Waterproof gloves. - Shoes plus socks. - Protective eye wear. Corn In addition to the PPE for all handlers, mixers and loaders must use Engineering Controls that meet the requirements listed in the WPS for agricultural pesticides (40 CFR 170. 607(d)(2)(i) &(ii) for dermal and inhalation protection. Except when using an enclosed cab that meet the requirements listed in the WPS for agricultural pesticides (40 CFR 170. 305) for dermal and inhalation protection, applicators must wear the following PPE in addition the PPE required for all handlers: - A NIOSH approved particulate respirator with any N, R, or P filter with NIOSH approval number prefix TC-84A. Higher-level respirators that are NIOSH approved for particulates can also be used.
      Tankmix Compatibility
      COMPATIBILITY TESTING AND TANK MIX PARTNERS Compatibility If TRIVOLT HERBICIDE is to be tank mixed with liquid fertilizers or other pesticides, compatibility needs to be tested prior to mixing. To test for compatibility, use a small container and mix a small amount (0.5 to 1 qt) of spray, combining all ingredients in the same ratio as the anticipated use. If any indications of physical incompatibility develop, DO NOT use this mixture for spraying. Indications of incompatibility usually will appear within 5-15 minutes after mixing. Read and follow all parts of the label of each tank-mix product. It is the pesticide user's responsibility to ensure that all products are registered for the intended use. Read and follow the applicable restrictions and limitations and directions for use on all product labels involved in tank mixing. Users must follow the most restrictive directions for use and precautionary statements of each product in the tank mixture. Order of Mixing TRIVOLT HERBICIDE may be used with other specified pesticides, fertilizers, and micronutrients. The proper mixing procedure for TRIVOLT HERBICIDE application with water or liquid fertilizer as a carrier: 1. Fill the spray tank 1/4 to 1/2 of the required volume of water or liquid fertilizer prior to the addition of TRIVOLT HERBICIDE. 2. Add the proper amount of TRIVOLT HERBICIDE, then add the rest of the water or liquid fertilizer to the desired level. 3. Maintain sufficient agitation to ensure a uniform spray mixture during application. 4. If TRIVOLT HERBICIDE is applied in a tank mixture with other pesticides, add TRIVOLT HERBICIDE to the spray tank first and ensure it is thoroughly dispersed before adding other pesticides. 5. Continue to fill the tank with carrier to the desired volume while agitating. Continue agitation during application to ensure a uniform spray mixture.


Recommended Agronomy Resources