Use & Mixing

The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Please click on 'Labels / MSDS' in the left hand navigation for special or state label instructions. Always read and follow label instructions.

Harness Xtra Herbicide

Instructions
MIXING, SPRAYING AND HANDLING INSTRUCTIONSNOTE: Direct contact or exposure to this product or spray mixtures of this product should be minimized. The following instructions for transfer, mixing, cleaning or repairing equipment should be followed in order to minimize this exposure. Review the protective clothing requirements as listed in the PRECAUTIONARY STATEMENTS section of this label and do not use this product until you have the necessary protective clothing.2.5 Gallon ContainersOpen pouring from these containers can result in exposure from splashing or spilling.Special care in lifting and pouring is strongly recommended.Bulk ContainersOpen pouring from these containers can result in exposure from splashing or spilling and is not recommended. This product should be transferred from these containers to the mix or spray tank using pumps or transfer probes. The probe or pump should not be removed from the container or disconnected until the container is emptied and rinsed.Use the pump or probe system to rinse the empty container and transfer the rinsate directly to the mix or spray tank.
Reentry PPE
PPE required for early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, are: coveralls, chemical-resistant gloves made of any waterproof material and shoes plus socks.
PPE
Some materials that are chemical-resistant to this product are listed below. If you wantmore options, follow the instructions for category A on an EPA chemical-resistancecategory selection chart.Mixers, loaders, applicators and other handlers must wear: long-sleeved shirt and long pants, chemical-resistant gloves such as polyethylene or polyvinylchloride, shoes plus socks, and a chemical-resistant apron when mixing/loading, cleaning up spills, or cleaning equipment, or otherwise exposed to the concentrate.
Tankmix
Sprayer CompatibilityAlways predetermine the compatibility of this product or labeled tank mixtures of thisproduct with water carrier or sprayable fluid fertilizer carrier by mixing small proportional quantities in advance. See the STANDARD SPRAYABLE FLUID FERTILIZER COMPATIBILITY TEST section in this label to determine the compatibility of this product and the labeled tank mixtures recommended for use with sprayable fluid fertilizer carrier.Mix this product or labeled tank mixture of this product with the appropriate carrier asfollows:1. Place a 20- to 35-mesh screen or wetting basket over filling port.2. Through the screen, fill the sprayer tank one-half full with the appropriate carrier.3. If a compatibility agent is necessary to improve mixing or to prevent the formation ofundesirable and unsprayable gels or precipitates, while agitating add it to the carrieralready in the tank. Use only compatibility agents cleared by FDA for this use. Read andfollow all directions for use, cautionary statements and all other information appearingon the selected compatibility agent label. Check for adequate agitation.4. If a wettable powder or dry flowable formulation is used, make a slurry with water andadd it slowly through the screen into the tank. Continue agitation.5. If a flowable formulation is used, add slowly through screen into the tank. Mixing andcompatibility may be improved when flowable is premixed one part flowable with one part water and added to the tank in diluted form.6. Add this product slowly through the screen into the tank. Mixing and compatibility maybe improved when this product is prediluted with two parts of water and added to thetank in diluted form.7. Complete filling the sprayer tank with carrier. If a Roundup agricultural herbicide orGramoxone brand herbicide is used, add the required amount near the end of the fillingprocess. Remove hose from tank immediately after filling to avoid siphoning back intothe carrier source.Maintain good agitation at all times until the contents of the tank are sprayed.NOTE: If spray mixture is allowed to settle at any time, thorough agitation is required to resuspend the mixture before spraying is resumed.Keep by-pass line on or near bottom of tank to minimize foaming. Screen size in nozzle orline strainers should be 50-mesh. Carefully select proper nozzle to avoid spraying a finemist. Check for even distribution of spray droplets. To reduce loss of the chemical due to drift of a fine mist, apply at nozzle pressures below 40 psi.

Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email or call 1-866-99-BAYER.
Copyright © Bayer CropScience