Use & Mixing

The instructions for use and mixing described below are from the Environmental Protection Agency approved Federal Label. Please click on 'Labels / MSDS' in the left hand navigation for special or state label instructions. Always read and follow label instructions.

Wolverine

Instructions
MIXING INSTRUCTIONSWolverine Herbicide must be applied with clean and properly calibrated equipment. Prior to adding Wolverine Herbicide to the spray tank, ensure that the spray tank, filters and nozzles have been thoroughly cleaned. In-line strainers and nozzle screens should be 50 mesh or coarser.1. Fill the spray tank 1/4 to 1/2 full with clean water then add AMS or UAN and begin agitation or bypass.2. Add the appropriate rate of Wolverine Herbicide directly to the spray tank. Maintain sufficient agitation during both mixing and application.3. Add a listed tank mix partner, if desired.4. Add surfactant if desired.5. Fill the spray tank with balance of water needed.6. Continue agitation during Wolverine Herbicide application to ensure uniform spray coverage.
Reentry PPE
For early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, wear: coveralls over long-sleeved shirt and long pants; socks and chemical resistant footwear. Wear goggles or face shield, and chemical resistant gloves (such as nitrile, butyl, neoprene, and/or barrier laminate).
PPE
Some materials that are chemical-resistant to this product are listed below. If you want more options, follow the instructions for category A on an EPA chemical resistance category selection chart.Applicators and other handlers must wear: Long-sleeved shirt and long pants, socks, shoes, chemical resistant gloves such as barrier laminate, butyl rubber >= 14 mils, nitrile rubber >= 14 mils, or neoprene rubber >= 14 mils, and protective eyewear (safety glasses).Follow manufacturer's instructions for cleaning/maintaining PPE. If no such instructions for washables exist, use detergent and hot water. Keep and wash PPE separately from other laundry.Discard clothing and other absorbent materials that have been drenched or heavily contaminated with this product's concentrate.Do not reuse them. Follow manufacturer's instructions for cleaning/maintaining Personal Protective Equipment (PPE). If no such instructions for washables, use detergent and hot water. Keep and wash PPE separately from other laundry.
Tankmix
Compatibility Testing With Tank Mix PartnersIf Wolverine Herbicide is to be tank mixed with other pesticides, compatibility should be tested prior to mixing. To test for compatibility, use a small container and mix a small amount (0.5 to 1 qt) of spray, combining all ingredients in the same ratio as the anticipated use. If any indications of physical incompatibility develop, do not use this mixture for spraying. Indications of incompatibility usually will appear within 5-15 minutes after mixing. Read and follow the label of each tank-mix product used for precautionary statements, directions for use, geographic and other restrictions.Tank mixtures For Insect ControlWolverine Herbicide may be tank mixed with Baythroid(R) XL, Mustang Max(TM), or Warrior(R) insecticides providing proper timing for insect and weed control are the same.Tank mixtures For Disease Control Fungicides such as Stratego(R), Tilt(R), Headline(R), mancozeb (Dithane F-45(R); Manzate(R) 75DF; Penncozeb(R) 75DF), or Topsin(R) M may be tank mixed with Wolverine Herbicide when timing for application of each tank mix partner is the same for the use site. Do not apply Wolverine Herbicide in tank mixture with tebuconazole.Tank mix applications of herbicides with fungicides may cause temporary yellowing, leaf burn and or height reduction of the crop.Refer to the specific fungicide label for use directions, application rates, restrictions and a list of diseases controlled.

WOLVERINE PowerPak

Reentry PPE
Do not enter or allow worker entry into treated areas during the restricted entry interval (REI) of 24 hours. For early entry to treated areas that is permitted under the Worker Protection Standard and that involves contact with anything that has been treated, such as plants, soil, or water, wear: coveralls over long-sleeved shirt and long pants; socks and chemical resistant footwear. Wear goggles or face shield, and chemical resistant gloves (such as nitrile, butyl, neoprene, and/or barrier laminate).
PPE
Applicators and other handlers must wear: Coveralls over short-sleeved shirt and short pants, socks, chemical resistant footwear, chemical resistant gloves such as barrier laminate, butyl rubber >= 14 mils, nitrile rubber >= 14 mils, or neoprene rubber >= 14 mils, and protective eyewear (goggles or face shield).
Tankmix
TANK MIX DIRECTIONS Compatibility Testing With Tank Mix Partners If WOLVERINE(TM) PowerPak is to be tank mixed with other pesticides, compatibility should be tested prior to mixing. To test for compatibility, use a small container and mix a small amount (0.5 to 1 qt) of spray, combining all ingredients in the same ratio as the anticipated use. If any indications of physical incompatibility develop, do not use this mixture for spraying. Indications of incompatibility usually will appear within 5-15 minutes after mixing. Read and follow the label of each tank-mix product used for precautionary statements, directions for use, geographic and other restrictions. Use in accordance with the most restrictive label limitations and precautions. Tank mixtures For Disease or Insect Control WOLVERINE(TM) PowerPak may be tank mixed with Baythroid(R)XL, Mustang Max(TM), Sevin(R) XLR PLUS or Warrior(R) insecticides providing proper timing for insect and weed control are the same. Fungicides such as Stratego(R), Headline(R), mancozeb (Dithane F-45(R); Manzate(R) 75DF; Penncozeb(R) 75DF), Tilt(R), or Topsin(R)M may be tank mixed with WOLVERINE(TM) PowerPak when timing for application of each tank mix partner is the same for the use site. Tank mix applications of herbicides with fungicides may cause temporary yellowing, leaf burn and or height reduction of the crop. Refer to the specific fungicide label for use directions, application rates, restrictions and a list of diseases controlled. WOLVERINE TM PowerPak must be applied with clean and properly calibrated equipment. Prior to adding WOLVERINE TM PowerPak to the spray tank, ensure that the spray tank, filters and nozzles have been thoroughly cleaned. In-line strainers and nozzle screens should be 50 mesh or coarser. 1. Fill the spray tank 1/4 to 1/2 full with clean water then add AMS or UAN and begin agitation or bypass. 2. Add the appropriate rate of WOLVERINE TM PowerPak directly to the spray tank. Maintain sufficient agitation during both mixing and application. 3. Add recommended tankmix partners, if desired. 4. Add surfactant if desired. 5. Fill the spray tank with balance of water needed. 6. Continue agitation during WOLVERINE TM PowerPak application to ensure uniform spray coverage. TANK CLEANUP PROCEDURE 1. Drain the tank completely, and then wash out tank, boom and hoses with clean water. Drain again. 2. Half fill the tank with clean water and add ammonia (i.e., 3% domestic ammonia solution) at a dilution rate of 1% (i.e., 1 gallon of domestic ammonia for every 100 gallons of rinsate). Complete filling of the tank with water. Agitate/recirculate and flush through boom and hoses. Leave agitation on for 10 minutes. Drain tank completely. 3. Repeat step 2. 4. Remove nozzles and screens and soak them in a 1% ammonia solution. Inspect nozzles and screens and remove visible residues. 5. Flush tank, boom, and hoses with clean water. 6. Inspect tank for visible residues. If present, repeat step 2.
Always read and follow label instructions. Not all products are registered for use in every state. Please check with Bayer or your local Lead State Agency for product registration status. If you wish to find out if a product is registered in your state or for additional product information, send us an email or call 1-866-99-BAYER.

View all labels / MSDS

Protect your crop quality and yield potential for an optimal harvest. » more
Copyright © Bayer CropScience